Updated November 2026

VPN connections drop. A server restarts, your internet blips, or the provider rotates a key. The question is what your devices do in the few seconds or minutes before the tunnel comes back.

A kill switch decides that. Here is how it works on a router, why auto-reconnect is not the same thing, and how to check that yours actually works.

The short answer

A kill switch blocks internet traffic for chosen devices whenever the VPN tunnel is down, so nothing goes out over your regular ISP connection. Without one, most routers "fail open" and quietly send traffic outside the VPN until it reconnects. On a router you set it once and it covers every device behind it.

The basics

How a kill switch works

A router VPN can fail in one of two ways when the tunnel drops:

  • Fail open: the router falls back to your normal ISP connection. Devices stay online, but their traffic and your real IP are exposed until the VPN reconnects.
  • Fail closed: the router blocks traffic for VPN devices until the tunnel is back. Devices lose internet for a moment, but nothing leaks. This is what a kill switch does.

On a computer or phone, a kill switch is a setting in the VPN app. On a router, it is a firewall rule that only lets VPN devices reach the internet through the tunnel.

Common mix-up

Auto-reconnect is not a kill switch

Most VPN router firmware reconnects on its own after a drop. That's good, but it only shortens the gap. During the gap, a router without a kill switch still sends traffic out through your ISP.

When you set up a VPN router, look for two separate things: automatic or persistent reconnection, and a setting that explicitly blocks non-VPN traffic when the tunnel is down. You want both.

From our support desk

If your router's VPN setting says something like "block" or "kill switch", that's the fail-closed option. If it only mentions reconnecting or retry intervals, it isn't a kill switch on its own.

Planning

Kill switches and device exceptions

Many households send some devices through the VPN and leave others on the regular connection, using policy-based routing. The kill switch should follow the same split.

  • VPN devices (a laptop, a streaming box) should be blocked when the tunnel is down.
  • Direct devices (a work laptop on its own VPN, a doorbell camera, a game console) should keep working through your ISP.

This is one of the reasons a router kill switch beats an app. It protects the TV and the streaming stick that can't run a VPN app at all, while leaving the devices you excluded alone.

Check

How to test your kill switch

  1. On a VPN device, check your public IP at an IP lookup site. It should show your VPN location.
  2. Make the tunnel fail without switching the VPN off, for example by editing the VPN profile to point at a server address that doesn't exist. On some firmware, turning the VPN off by hand also turns off its block, so that isn't a real test.
  3. On the same device, try to load a new site. With the kill switch on, it should fail to load.
  4. Check a device you excluded from the VPN. It should still browse normally.
  5. Put the correct server back and confirm the VPN device comes back online with the VPN location.

If step 3 loads the page and the IP lookup shows your real location, the router is failing open. Our post on what happens when a router VPN disconnects goes deeper into reading the result.

Setup

Setting it up on your router

Every firmware names the setting differently, but the decision is the same: which devices should lose internet when the VPN is down.

  • Privacy Hero 2: setup is browser-based and guided. You choose your provider, then decide which devices use the VPN. If you're not sure the block is on, ask us and we'll check it with you.
  • Other VPN routers: look in the VPN client or device routing settings for an option that blocks traffic when the VPN is down. Names vary by firmware and version.
  • Set routing first: choose which devices use the tunnel, then turn the block on, so it covers the right devices.

Go deeper

FAQ

Frequently asked questions

Do I need a kill switch on a VPN router?

If you use the VPN for privacy or to keep a streaming location consistent, yes. Without one, most routers send traffic over your regular connection whenever the tunnel drops.

Will a kill switch cut off my whole network?

Only if every device goes through the VPN. With device-based routing, the kill switch blocks only the VPN devices and leaves excluded ones online.

Is auto-reconnect the same as a kill switch?

No. Auto-reconnect brings the VPN back after a drop. A kill switch blocks traffic during the drop. You want both turned on.

Does a kill switch slow down my VPN?

No. It is a firewall rule that only matters when the tunnel is down. It doesn't affect speed while the VPN is connected.

Why did my devices lose internet with the VPN on?

If the tunnel failed to connect or dropped, the kill switch is doing its job. Check the VPN status in the router first, then the provider's server and your login details.

For everything else about VPN routers, from setup behind your ISP's box to picking a provider, see our VPN Router Guide.

Want us to check your kill switch?

Tell us your router and VPN provider. We'll confirm the block is on for the right devices, so nothing slips out when the tunnel drops.

Talk to an expertTake the Router Quiz

100,000+ Routers Shipped · 15+ Years of VPN Expertise · Official NordVPN Partner · US-Based Experts